Heavy Bonding Ceramic Wall Swimming Pool Tile Adhesive , Mosaic
PB-106 Super Tile Adhesive (C2)
White, gray power
Good anti-infiltration and anti-aging function, no shrink, strong bond ability, Non-toxic, Eco Friendly, small shrinking rate
Swimming pool, outdoor wall, ground, platform and balcony
Firm, dry and clean, no grease, no wax, or other loose materials
Surface Dry Time
PB-106 Super Tile Adhesive (C2) is a kind of high quality
environment-friendly waterborne powder which can be mixed with
water and used for bonding ceramic tile on the surfaces of wall,
ground and floor. It is easily applied and can achieve an excellent
PB-106 is a kind of synthetic rubber latex, mixing with the ceramic
tile adhesive Ⅲ (premixed graded fine sand, special additives and
synthetic resin) to form a high viscosity achieve, which can be
used in all kinds of construction surface. PB-106 can also be mixed
with sand and cement. The adhesive can harden without obvious
shrinkage. It will not slip off when pasting a heavy ceramic tile
in the vertical surface.
Emulsion and powder or cement mixed with sand used in:
1, Stickup ceramic tile, stone and mosaic on all sorts of wall,
2, Stickup all kinds of nature stone inside and outside.
3, After emulsion mixed with cement mortar,scraping a thin layer
1, Bond glass Mosaic, quarry tile and brick in the swimming pool.
2, Bond glass Mosaic, quarry tile and brick on the outdoor wall,
platforms and the balcony.
3, Bond all kinds of ceramic tile in which in need to specific
places where chemical resistance such as dairy,
brewery, wine cellar, food and chemical industry.
4, Bond all kinds of ceramic tile on the ground buried geothermal
heat preservation equipment.
5, Bonding marble and other natural stone with cement mortar in
outdoor wall, platform and balcony to
make a thin layer.
Can not be used in the following situations:
1, Never can be used on the wall or ground with severe deformation
2, Unstable concrete or fabrication without adequate maintenance.
3, Metal surface.
4, When using PB-01 General Tile Adhesive,the chromatic aberration
between tint glass mosaic and
surface material should be reduced to a minimum.
1, Substrate Preparation
1) The substrate surface should be firm, dry and clean, no grease,
no wax, or other loose materials.
2) The cement surface should not be shrinking after pasting the
3) Each 1cm-thick plastering should be maintained at least 1 week.
4) Cooling the substrate when it is too hot.
2, Application of Adhesive:
1) Use a notched trowel to paste the adhesive. The general
principle of choosing a correct trowel is that the coverage in the
interior wall and lightloading area is at least 65~70%, while 100%
in the exterior wall and overloading area.
2) Paste one layer on the surface with the flat surface of the
trowel to reach a high-bond-strength effect, then choose the size
of the notched trowel according to the size and type of the ceramic
Typical ceramic tile
Normal ceramic tile
Ground,plane, or the ceramic tile uneven
Pinbang notched trowel type
Square No.4, about 2~2.5kg/㎡
Type V No.5, about 3kg/㎡
Type V No.6, about 5kg/㎡
In demanding situations, such as the 300×300mm ceramic tile in
exterior wall, ground, swimming pool and pool, and the ground which
is overloading or need to be polished, just paste the adhesive
evenly on the back of the ceramic tile(dorsal division).
3, Lay-up Ceramic tile:
1) No need to wet the ceramic tile and stone before laying, unless
there is much dust on the back of the ceramic tile.
2) In order to maintain a good contact with adhesives, the ceramic
tile should be pressed hard in place.
3) The open assembly time of PB-106 in normal temperature and
humidity is about 20 minutes. In the conditions of adverse climatic
(burning sun, dry wind, high temperature, etc.) or strong
water-absorption of the surface, open assembly time may be
shortened, sometimes reduced to a few minutes. So always check
carefully whether the adhesive surface peeling, or whether it is
still in a sticky situation. If it is peeling already, pasting the
adhesive one more time. Wetting the surface before pasted the
adhesive helps to extend the open assembly time.
4) Wetting the adhesive when it is peeling is not recommended, or
it would form a nonstick film instead of dissolving.
5) If necessary, the seam should be adjusted within 60 minutes
after laying bricks.
6) It can not be washed or in the rain within 24 hours after laying
bricks, and avoid placing in cold or exposed situation for 5~7
1) Fill the wall seam with Pinbang special cement base or epoxy
grout after laying 4~8 hours while fill the floor seam after laying
24 hours. And there are many kinds of color of grout can be
2) Use Pinbang grout to fill the crack.
3) Available for walking: about 24 hours after laying.
4) Available for use: the surface can be used about 14 days later
while the swimming pool 21 days later.
Tools can be cleaned with plenty of water before the Pinbang Super
Tile Adhesive (C2 standard) dried, or cleaning will be difficult,
but it still can be cleaned with Pinbang cleaner.
Store in cool and dry place, unopened product can be saved for one