Strong Cohesive Force Ceramic Wall Tile Adhesive On Floor For
PB-303 Super Stone Adhesive (C2 )
White, gray power
No-toxic, environment friendly, high thixotropy, material-saving, strong bonding power, no shrink, long open assembly time
Firm, dry and clean, no grease, no wax, etc
Ceramic tile, stone and mosaic on all sorts of wall, ground, plasterboard
Surface Dry Time
PB-303 Super Stone Adhesive (C2) is a kind of high quality
environment-friendly waterborne powder which can be mixed with
water and used for bonding ceramic tile on the surfaces of wall,
ground and floor. It is easily applied and can achieve an excellent
adhesion.It has strong cohesion force. Reduce the common phenomenon
of tiles detaching and peeling when pasted by Portland cement.
PB-303 is a gray powder developed by PB test center, consists of
cement, graded fine sand, synthetic resin and special additives.
Forming a kind of ceramic tile adhesive when stirred with water:
1, Easy to paste.
2, High thixotropy, even if the heavy brick is not inserted into
the interval, it will not collapse when applied in the vertical
3, Strong bonding power, can perfectly bonded together with all
kinds of traditional building materials.
4, No shrinkage after it is dry and hard.
5, Long open assembly time.
1, Pasting ceramic tile, stone and mosaic on all sorts of wall,
ground, and even the ceiling indoor and outdoor.
2, Fixed-point bonding heat-preservation, such as expanded
polystyrene, stone and glass fiber, wood cement board, silencer
Pasting the tile adhesive and mosaic in the following base:
1, Cement mortar or plastering wall.
2, Indoor aerated concrete brick wall.
4,The ground buried geothermal insulated equipment.
5, Fully maintained and drying concrete layer.
6, Firm interior-wall paint.
PB-303 cannot be used on the following surface layer:
1, Concrete members which are possibly serious shrinking.
2, Wall and floor which are strongly out of shape and shaky.
3, Metal face.
1, Preparation on the surface layer
1) The substrate surface should be firm, dry and clean, no grease,
no wax, etc. Damp surface may extend the setting time of adhesives.
2) After laying on the surface of the ceramic tile, cement base
should not be contraction, so in spring and summer, each 1cm-thick
wall plastering should be maintained at least 1 week. Cement bottom
ash should be maintained at least 28 days.
3) Should take steps to lower the temperature if the surface is too
1) Mixed and stirred PB-303 Super Stone Glue with water into paste,
then put it aside for a few minutes and then a little stirring to
gain the better effect.
2) The ratio between the weight and water consumption of the gray
PB-303 should be 100:27~28, amounting to per 20kg powder adds 5.5
to 6.5L of water, while the white one should be 100:30~32,
amounting to per 20kg powder adds 6.5 to 7.5L of water.
3) The mixing material in the preparation can be saved for 8 hours.
3, Lay-up Ceramic tile and stone
1) No need to wet the ceramic tile and stone before laying, unless
there is much dust on the back of the ceramic tile.
2) In order to maintain a good contact with adhesives, the ceramic
tile should be pressed hard in place.
3) The open assembly time of PB-106 in normal temperature and
humidity is about 20 minutes. In the conditions of adverse climatic
(burning sun, dry wind, high temperature, etc.) or strong
water-absorption of the surface, open assembly time may be
shortened, sometimes reduced to a few minutes. So always check
carefully whether the adhesive surface peeling, or whether it is
still in a sticky situation. If it is peeling already, pasting the
adhesive one more time. Wetting the surface before pasted the
adhesive helps to extend the open assembly time.
4) Wetting the adhesive when it is peeling is not recommended, or
it would form a nonstick film instead of dissolving.
5) If necessary, the seam should be adjusted within 60 minutes
after laying bricks.
6) It can not be washed or in the rain within 24 hours after laying
bricks, and avoid placing in cold or exposed situation for 5~7
4, Gap filling and sealing
1) Fill the wall seam with Pinbang special cement base or epoxy
grout after laying 4~8 hours while fill the floor seam after laying
24 hours. And there are many kinds of color of grout can be
2) Use Pinbang grout to fill the crack.
Store in cool and dry place, unopened product can be saved for one